#1
|
|||
|
|||
Cautionary tale (happy ending though)
The action up the neck on my 415 had risen a little... not a big deal so I hadn't done anything about it... but it occurred to me how great it'd be to address that issue before the nice series of gigs my duo will soon be playing.
So I called my regular repair shop and asked about expediting: they said to call back after lunch to confirm, but that they could probably get me in and out by Saturday. But then on a lark, I called the place I bought it from 15 years ago. They said no problem, they could do a setup for me while I waited. Great! I drove the 30 miles and played a bunch of guitars while the work occurred. When I received my Taylor, the action was much improved *but* they'd cut my saddle down by about 2/3rds! I am normally not too picky/dramatic, but the loss in power/volume was noticeable, especially factoring in the new strings. So today, I took the guitar to my main shop and 'fessed up. They agreed that there was no need to sacrifice the saddle on a Taylor. Long story short is that by Saturday's gig the NT neck will be adjusted and I'll have a new, full-height saddle. Whew! Lessons learned: 1) don't rush on a whim; and 2) be loyal to a sure thing.
__________________
Respectfully, Mike Taylor 415 --- Epiphone Texan --- Collings D1A --- Martin 5-15 --- etc Take a sad song and make it better. |
#2
|
||||
|
||||
and lesson 3) always call back the shop that incorrectly hacked your guitar and reprimand them
__________________
Fazool "The wand chooses the wizard, Mr. Potter" Taylor GC7, GA3-12, SB2-C, SB2-Cp...... Ibanez AVC-11MHx , AC-240 |
#3
|
|||
|
|||
They took THAT approach to your request WITHOUT consulting you when you were IN THE STORE! That's just ludicrous!
|
#4
|
|||
|
|||
Lesson #1 should be that the action on a Taylor is set by adjusting the neck angle rather than sanding the saddle as on a set neck instrument. Don't let people who don't understand this basic fact work on your guitar.
|
#5
|
|||
|
|||
Quote:
Any idea what the cost range for that is? |
#6
|
|||
|
|||
Quote:
We always go over exactly what needs to be done, and exactly how it's going to be done. In the end, there are never any surprises. It's your guitar. Take control of what's done to it. Bottom line. Be willing to drive a little further, and maybe wait a little longer. |
#7
|
|||
|
|||
Quote:
Taylor necks are typically reset this way for routine action adjustments. If the tech knows what he's doing and has been through the Taylor tech school, it doesn't take any longer than a typical set up and costs about the same. This is why Taylor recommends having your guitar serviced only by certified techs that have been trained at the Taylor factory. The loss of tone, volume etc. has to do with a lower break angle because of the lower saddle after sanding, or so I was told by a tech at the factory. |
#8
|
|||
|
|||
Quote:
|
#9
|
|||
|
|||
Quote:
I picked up my 15-yr-old Taylor 415 from my main shop and have a new, tall saddle AND proper action with tone restored. They charged me for a normal tune-up, although I did need a new saddle since the first shop had shaved it down. BTW our gig last night was a surprise 40th birthday party in the back yard of a beautiful house on a lake. So great to be a part of such a wonderful evening.
__________________
Respectfully, Mike Taylor 415 --- Epiphone Texan --- Collings D1A --- Martin 5-15 --- etc Take a sad song and make it better. |
#10
|
|||
|
|||
+1: What Terrapin said!
__________________
The Electrics check The Acoustics Tom Doerr - Trinity. Flamed Maple under Swiss Tom Doerr - M/D. Braz under Red |